D12 amplifier

The 3 RU two channel D12 amplifier delivers medium to high power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D12 contains setups for all d&b loudspeakers and a linear mode. The signal delay capability enables user definable settings of up to 340 msec (=100 m/328.1 ft) to be applied independently to each channel. The same applies to the 4-band parametric equalizer, providing optional boost/cut or notch filtering. The D12 incorporates a digital rotary encoder and a LCD display to configure the amplifier.

The D12 utilizes an autosensing switch mode power supply for mains voltages 120 V/230 V, 50 - 60 Hz (optional 100/200V). The D12 amplifier incorporates d&b SenseDrive for accurate control of LF drivers in d&b loudspeakers driven in 2-Way Active mode or in actively driven d&b subwoofers. When the D12 is fitted with EP5 connectors and appropriate 5 wire cabling, d&b SenseDrive can be used, resulting in an extremely precise bass performance even at high levels. NL4 and NL8 connector options are also available. RJ 45 connectors enable access to the Remote network via CAN-Bus. d&b System check verifies that the system performs within a predefined condition, whilst d&b Load monitoring enables an automatic and continuous impedance monitoring. Both can determine the status of an LF or HF driver in systems with multiple elements, even if these are crossed over passively.

Data

Data

控制和指示
电源 主电源开关
滚动/编辑 数字旋转编码钮
显示 液晶显示器 (LCD)/120 x 32 像素
ISP, GR, OVL A/B LED指示灯
数字信号处理
均衡器 4 段参量/陷波均衡器
延时模拟与数字输入 0.3 毫秒
延时设置 0.3 - 340 毫秒,0.1 毫秒步长
配置 当前 d&b 音箱与线性模式
功能开关 d&b 音箱专用电路
频率发生器 粉红噪声或正弦波
采样率 96 kHz/27 位ADC(模数转换) /24 位DAC(数模转换 )
接头
输入模拟(A1、A2) 3 针卡侬母头
模拟链路(A1、A2) 3 针卡侬公头
输入数字(D1、D2) 3 针卡侬母头 AES 3
数字链路 (输出) 3 针卡侬公头
采样率 48 kHz/96 kHz
输出通道 A/B NL4
可选 EP5/NL8
远程 2 x RJ 45 并联、CAN-Bus 总线
服务 SUB-D9 母头
电源接头 powerCON®
数据(带次低频滤波的线性设置)
额定输出功率 (THD + N < 0.1%),
双通道驱动
2 x 750 W,8 欧姆
2 x 1200 W、4 欧姆
信噪比(无计权不计权,RMS) > 110 dBr
电源
自动检测开关式电源 115/230 V,50 - 60 Hz
可选 100/200 V,50 - 60 Hz
尺寸、重量
高 x 宽 x 深 3 RU x 19” x 353 mm/13.9”
重量 13 kg/28.7 lb

D6、D12 与 D80 功放比较

Documentation

Documentation

Title Language Date Size
D12 Firmware V2.32 Release notes International 23.11.2015 77 KB
D12 Hardware manual 4.9 English 26.02.2014 607 KB
D12 Software manual 5.5 EN English 28.02.2013 601 KB
EU Declaration of Conformity (CE) International 04.10.2016 51 KB
The Amplifiers/Software brochure English 06.04.2018 7 MB
TI 315 D12 AES/EBU Input and Wiring English 27.08.2008 403 KB
TI 330 Cardioid Subwoofer Array - CSA English 08.09.2016 263 KB
TI 340 D12 SenseDrive English 11.03.2010 101 KB

Downloads

Architectural specifications

Architectural specifications

Architects' and engineers' specification
The amplifier shall be dual channel incorporating digital signal processors (DSP) to provide loudspeaker specific configurations and functions for d&b loudspeakers. It will be equipped with digital and analog signal inputs as well as link outputs, remote control and monitoring capabilities and sophisticated protection circuits.
It will have a temperature and signal controlled fan to cool the internal assemblies. A user definable 4-band parametric equalizer, and signal delay capability of up to 340 ms shall be incorporated for independent application to each channel.
It will contain a signal generator offering pink noise or sine wave program.
Load monitoring and System check functions will be included to ascertain the status of the loudspeaker impedance. Load monitoring shall be included to allow impedance monitoring to determine the status of an LF or HF driver in systems with multiple elements, even if these are crossed over passively.
Load and Input Monitoring shall be suitable for use in applications compliant to EN 60849/IEC 60849 ‘Sound Systems for Emergency Purposes’.
Output configurations shall be selectable for dual channel, mixed TOP/SUB and 2-Way Active modes.
d&b SenseDrive will be incorporated for use with subwoofers and the LF drivers in active loudspeakers compensating for the influence of cables and to improve impulse response.
User interface shall be via a Liquid Crystal Display (LCD) in conjunction with a digital rotary encoder and via the d&b Remote network.

Power supply:
The power supply shall be autosensing switched mode for use with 115/230 V 50-60 Hz supplies (optional 100/200 V) fitted with a mains inrush current limiter, self-resetting over temperature and overvoltage protection.

Power amplifier:
The power amplifier channels shall have a switch on delay, DC protection, self-resetting over temperature protection, output short circuit and overload protection.

Rated output power (THD+N < 0.1%):
2 x 750 W into 8 ohms, both channels driven
2 x 1200 W into 4 ohms, both channels driven

Damping factor: (20 Hz - 1 kHz, Ref. 4 Ohm): >200
S/N ratio (unweighted, RMS): > 110 dBr
Output connectors: EP5*, NL4 and NL8* options.
*SenseDrive function only in conjunction with EP5 and NL8 connectors

Digital Signal Processing:
Sampling Rate: 96 kHz / 27 Bit ADC / 24 Bit DAC
Analog input latency: 0.3 ms (including conversion)
Delay: up to 340 ms (100 m/328 ft),
EQ: 4-band EQ with PEQ or Notch function
Frequency generator: pink noise and sine wave
Operator input inhibit/password protection

Analog inputs: 2 x XLR 3-pol. female, input impedance 44 kOhms, electronically balanced
Analog Link outputs: 2 x XLR 3-pol. male
Digital input (AES/EBU - AES 3): 1 x XLR 3-pol. female, input impedance 110 ohms, transformer balanced
Sampling: 48/96 kHz, 2Ch/n
Synchronisation: Word-Sync: PLL-locked to source (slave-mode)
Digital Link: 1 x XLR 3-pol. male, signal buffering (refresh), power fail bypass relay

Level control (input sensitivity): – 57.5 dB ... +6 dB with 0.5 dB detents.

Dimensions: (HxWxD): 3 RU x 19" x 353 mm / 13.9"
Weight: 13 kg / 29 lb

Manufacturer: d&b audiotechnik GmbH