 |
|
Amplifiers.
Applications.
Data.
Downloads.
Documentation.
Accessories.
Q10 loudspeaker
The Q10 is a 110° x 40° passive two-way loudspeaker housing two 10" LF drivers and a 1.3" HF
compression driver with a rotatable constant directivity horn and a passive crossover network.
The two 10" neodymium LF drivers are positioned in a dipolar arrangement providing exceptional
vertical dispersion control with the nominal angle being maintained down to 400 Hz. The Q10
can be used as a stand-alone full range system or in combinations with other Q-Series cabinets
ground stacked, or mounted on a high stand with the Q Flying bracket. When used in the upright
configuration it has a very accurate 110° horizontal constant directivity behaviour that is
maintained down to approximately 800 Hz. Its wide constant directivity performance provides
remarkable transparency when used in close proximity to listeners. It is also ideally suited to
ambient and /or distributed sound reinforcement tasks where orientation within the sound field
is critical. The Q10 cabinet is constructed from marine plywood and has an impact resistant paint
finish. The front of the loudspeaker cabinet is protected by a rigid metal grill, covered with a
replaceable acoustically transparent foam. The cabinet incorporates a pair of handles and mounted
on the rear panel are two EP5 or NL4 connectors wired in parallel.
Amplifiers
The Q10 can be driven either by d&b's D6 or D12 dual channel power amplifiers configured for the Q10.
More detailed information on specific loudspeaker setups with d&b amplifiers
is available either in the relevant loudspeaker or amplifier manuals.
Applications
|
|
| Live-music |
  |
|
| Playback |
|
|
| Speech |
|
|
| Stage monitor |
|
|
| Subwoofer |
|
|
Data
|
|
| Components |
2 x 10" driver / 1.3" compression driver |
|
Max. sound pressure (1 m, free field)  with D6 / D12 |
133 / 137 dB SPL |
|
| Power handling capacity (RMS / peak 10 ms) |
400 / 1600 W |
|
| Frequency response (-5 dB) |
60 / 100  Hz - 17 kHz |
|
| Nominal dispersion angle (h x v) |
110° x 40°   CD |
|
| Cabinets per channel D6 / D12 |
2 / 2  |
|
| |
|
| Dimensions mm (h x w x d) |
580 x 308 x 410 |
|
| Weight kg |
22 |
|
| Dimensions inch (h x w x d) |
22.8 x 12.1 x 16.1 |
|
| Weight lb |
49 |
|
 |
Application information is presented for guidance only. We reserve the right to make
any necessary changes to the products and the published specification. As part of our
ongoing product development program we try, where possible, to maintain the highest
degree of product compatibility.
| |
recommended use |
| CD |
loudspeaker with constant directivity horn |
| |
with subwoofer |
| |
SPL max peak, test signal: pink noise with crest factor 4 |
| |
standard/CUT mode |
| |
≥ 400 Hz in dipolar direction |
| |
horn 90° rotatable |
| |
in applications with low continuous levels or low ambient temperatures
up to three loudspeakers per channel D12 may be connected |
|
Top of the page.
Downloads
Polar data
2D CAD drawings (DWG)
3D CAD models (DWG, AutoCAD 2000)
3D CAD models (DWG, AutoCAD 2004)
Documentation
Order form
for printed documentation from d&b.
Accessories
Available PDF documents for the accessories can be found in
the table below the images.
|
|
|
|
|
|
Z5156
Q Flying adapter |
|
Z5020
Flying adapter 02 |
|
Z5025
Flying adapter 03 |
|
 |
Z5150
Q Swivel bracket |
|
Z5024
Loudspeaker stand adapter |
|
Z5010
TV spigot with fixing plate |
|
|
Z5015
TV spigot for Flying adapter 02 |
|
Z5012
Pipe clamp for TV spigot |
|
Z5048
Flying pin |
|
|
Z5013
Loudspeaker stand M20 with winder |
|
E6001
Loudspeaker stand |
|
Z5009
Loudspeaker stand with winder |
|
|
Z5043
Horizontal bracket |
|
Z5161
Q Flying bracket |
|
|
|
|
|
|
 |
|
|
Declaration of Conformity Loudspeaker/Amplifiers (CE)