 |
|
Amplifiers.
Applications.
Data.
Downloads.
Documentation.
Accessories.
FAQs.
Q1 loudspeaker
The Q1 is a passive two-way loudspeaker housing two 10" LF drivers positioned
in a dipolar arrangement and a 1.3" HF compression driver fitted to a toroidal
wave shaping device. The 75° constant directivity horizontal dispersion pattern
is maintained down to 400 Hz, while the vertical HF dispersion of 15° allows
the Q1 to be used to construct vertical columns that produce a curved coherent
wave front. The mechanical and acoustical design of the cabinet enables vertical
splay angles to be set between 0° and 14°. Q1 cabinets can therefore be
used in vertical configurations starting from two cabinets with a 15° to 30°
dispersion, up to twenty cabinets with a fully user and venue defined vertical profile.
The Q1 cabinet is constructed from marine plywood, incorporates a pair of handles
and has an impact resistant paint finish. The front of the loudspeaker is protected
by a rigid metal grill covered with replaceable acoustically transparent foam, and
two EP5 or NL4 connectors wired in parallel are mounted on the rear panel.
Amplifiers
The Q1 can be driven either by d&b's D6 or D12 dual channel power amplifiers configured for the Q1.
More detailed information on specific loudspeaker setups with d&b amplifiers
is available either in the relevant loudspeaker or amplifier manuals.
Applications
|
|
| Live-music |
   |
|
| Playback |
|
|
| Speech |
|
|
| Stage monitor |
|
|
| Subwoofer |
|
|
Data
|
|
| Components |
2 x 10" driver / 1.3" compression driver |
|
Max. sound pressure (1 m, free field)  with D6 / D12 |
135 / 139 dB SPL |
|
| Power handling capacity (RMS / peak 10 ms) |
400 / 1600 W |
|
| Frequency response (-5 dB) |
60 / 100  Hz - 17 kHz |
|
| Nominal dispersion angle (h x v) |
75° x 15°  |
|
| Cabinets per channel D6 / D12 |
2 / 2  |
|
| |
|
| Dimensions mm (h x w x d) |
308 x 580 x 410 |
|
| Weight kg |
22 |
|
| Dimensions inch (h x w x d) |
12.1 x 22.8 x 16.1 |
|
| Weight lb |
49 |
|
 |
Application information is presented for guidance only. We reserve the right to make
any necessary changes to the products and the published specification. As part of our
ongoing product development program we try, where possible, to maintain the highest
degree of product compatibility.
| |
recommended use |
| |
with subwoofer |
| |
from 2 up to 20 as array |
| |
SPL max peak, test signal: pink noise with crest factor 4 |
| |
standard/CUT mode |
| |
≥ 400 Hz in dipolar direction |
| |
in applications with low continuous levels or low ambient temperatures
up to three loudspeakers per channel D12 may be connected |
|
Top of the page.
Downloads
Polar data
Array calculators
2D CAD drawings (DWG)
3D CAD models (DWG, AutoCAD 2000)
3D CAD models (DWG, AutoCAD 2004)
Documentation
Order form
for printed documentation from d&b.
Accessories
Available PDF documents for the accessories can be found in
the table below the images.
|
|
|
|
|
|
Z5151
Q Splay link |
|
Z5152
Q Front link |
|
Z5153
Locking pins 8 mm |
|
 |
Z5156
Q Flying adapter |
|
Z5155
Q Hoist connector chain |
|
Z5159
Q Flying frame |
|
|
Z5048
Flying pin |
|
Z5160
Q Load adapter |
|
Z5147
Rota clamp |
|
|
|
|
|
 |
|
|
Declaration of Conformity Loudspeaker/Amplifiers (CE)